New KDLIGHT 7135 V3 17mm 8 x AMC7135 1-Cell 16-Groups Flashlight Driver Board ( 1 pc )
Ship in 1-3 business days Free World-wide Shipping
- current regulation for all output mode (no PWM flicks even at Low mode)
- PWM frequency is 15000hz
- as low as 3mA-5mA for low output mode
- 8 x AMC7135 380ma IC, Constant regulated at 3040mA for High mode
- 1oZ copper PCB, immersion gold surface
- 17mm diamter, 1.6mm double sided PCB and less than 5mm overall height that allow to be used on most of pill
- Spring material: Brass material with silver coated with good electrical conductivity
- Spring Dimension: 4.2mm (H), Spring Wire Size: 0.7mm
- total 16 programmable outputs
(Please ref to the user manual for detail output and connections)
- Input Voltage Support: 2.6V - 4.5V
- Battery types Support: 1 x Li-ion or 3 x NiMH / alkaline
- Mode Specifications:
Hi : 100% 3040mA
Med: 35% 1064mA
Lo: 2% 5mA
AUX0: Cycle between 15Hz/6.5Hz at 2 secs
AUX1: 2Hz Blink
|Input:||2.7V - 4.5V ( 1 x Li-ion or 3 x NiMH / Alkaline battery )|
|LED Support:||Cree XM-L / XM-L2 / XP-L / XP-L HI / P7 / SST50, etc. (3 x XP-E, 2 x XP-G wired in parallel)
|1. Constant Current
2. Battery reverse protection
3. Low voltage warning
When the voltage is below 2.8V, it changes to Low mode (1 ma) and flashing every 60 secs.
And the cut-off voltage is at 2.6V, LED will be turned off.
4. Memory / Non-memory function
Easily configurable by setting the output group.
|Dimension:||17mm (Dia.) x 1.6mm (Thickness of PCB) x 4.8mm (including all component)
* GND (the outer ring - either side) must be attached to metal with thermal eproxy to heatsink.
Optimal heatsink ensure constant regulation without thermal protection kicking -in (i.e. reducing output).
** Warranty does not cover user damage. Please make conduction test before connect to the LED.
1 x Driver Board
2 x DC Power Cable
1 x User manual
To get Volume Discounts,please TICK "Use volume discounts" during checkout.
You will see a bulk rate discount applied at the bottom of the shopping cart.
For higher volume discount rate, please contact us email@example.com directly.
|Quantity||3+ units||5+ units||10+ units|
|Rate||$4.67 shipped||$4.56 shipped||$4.44 shipped|
When you use bulkrate discount, a flat $1.70 of registered air mail fee will added to your shopping cart to ensure delivery of package.
Showing latest 4 entries. Click here to read all 8 reviews.
Strengths:Two Matching bodies, XM-Ls,fresh Batteries gives me a typical 2.78A With 105c driver & 3.05A with this Driver. Seems to maintain higher Comparative output as voltage falls down towards 3.8v. A little easier to solder leads to than 105c. Has "firefly" like low mode. I like having memory as optional.
Weaknesses:S3 bridge may be listed in backwards order?l/m/h, h/m/l. Had some leaching & crud formation around the S1 to S4 Solder pad bridging area? I miss having a standard low mode. Hope you're not expecting standard green circuit board material.
Summary:Solder connecting S3 gives me H/M/firefly(low).......haven't tested Memory yet. I like it like this as a semi-tactical 2 1/2 mode(so to speak)......
Strengths:This version is probably the cleanest and best made that I have seen. Larger soldering points is a big plus for me and my "all thumbs" hands. Setting up modes is easier than before and having the instructions sent with the board is really icing on the cake, compared to previous versions.
Weaknesses:I have not found any. The only thing I would like to see is that the spring not be there. I never use a spring on modded lights. I always solder the +wire direct, so I have to remove the springs each time. Maybe it could be optional or just come in the package with a spring.
Summary:Overall it's a great board at a great price.
Strengths:На свежих батареях дает 3 ампера! Можно отключить дурацкие мигающие режимы. Установил в TrustFire Z3.
Weaknesses:Слишком слабый минимальный режим. Таким только если на часы подсветить. Очень тесная плата - недобно провода припаивать.
Summary:Идеальный драйвер для маленького прожектора!
Strengths:- really giving 3A with fresh battery - larger soldering points than nanjg 105c - optional memory mode (see cons) - mode groups
Weaknesses:This is good linear driver but it has 3 big faults: - when memory mode is OFF and you have set 3 or more modes: Flashlight is on, you select second mode, stays here 1 or more seconds, and when you want switch to third mode, the ligh goes first of all to first mode and you must quickly switch over second to third mode to select it. - for switching the modes must first click be doubleclick. Why? - unusable low mode. 50mA version is good.
Summary:Instead of having option to set unusable blinking modes, i would like option to set 4 mode of 10mA, 50mA, 500mA and 3000mA.